Colours pavers
Semi-transparent
Stain guard
Price - 54.00 $ / unit In Stock 1x 3.78 Liters
Made of acrylic and urethane, NuLOOK® Tinted Protector is specially designed to protect concrete pavers. Semi-transparent, it modifies or rejuvenates the original colour of pavers. It prevents deterioration due to chemical products such as de-icing salts, while providing resistance to acids and alkalis. Its surface film forms an invisible bond that stops the penetration of contaminants, facilitating the maintenance of pavers. Water-based, NuLOOK® Tinted Protector does not release unpleasant fumes, and it is environmentally-friendly.
COVERAGE
3.78 L Cover up to 14 m2 (150 sq. ft.).
Coverage will depend on surface porosity and joint width.
Applying a thin coat of CLEAR LOOK PAVER PROTECTOR EV every two years will keep the surface looking like new.
STORAGE
Keep from freezing. Store in a cool, dry place.
PACKAGING
Size : 3.78 liters - 18.93 liters (special order)
BEFORE YOU BEGIN
• Do not apply to natural stone or to wet-cast pavers or stamped concrete. • Application to poured concrete: Visit techniseal.com for more information. • Apply only to bare material*, or to material previously sealed with this product or with Techniseal® Clear Look EV Protector. • Wait until the protector is worn before recoating the surface (minimum 2 years). • With the appropriate Techniseal® stripper, remove any unknown coating that was previously applied. • ALWAYS TEST on a small hidden area of approximately 0.4 m2 (4 sq. ft.) to ensure that result meets your expectations (see Warranty).
*ABSORPTION TEST: Sprinkle a few drops of water on surface. If water is absorbed, move on to the next point. If water is repelled, do not apply this product
SURFACE PREPARATION (ESSENTIAL)
1.Cover vegetation, vehicles and adjacent surfaces that are not to be treated.
2.Remove stains with the appropriate Techniseal® cleaner.
3.Prepare the entire surface with Techniseal® HD Paver Preparator (efflorescence cleaner), as directed on product label.
APPLICATION
Application Conditions:
• Surface must be clean, dry and warm to the touch.
• Temperature must be between 10°C and 30°C.
• No rain forecasted for the next 24 hours.
• Sprinkler system must be turned off.
• Use a consistent application method over entire surface.
Necessary Tools:
• Low-pressure airless sprayer (< 50 psi) or pump sprayer
• 10 to 12 mm polyester nap roller, and paint tray
Do not dilute. Shake well or stir product before and during application. Intermix cans of the same product to ensure colour uniformity. Do not trim; use a cardboard for edges.
Work in sections of no more than 4.6 m2 (50 sq. ft.). Using the sprayer, saturate the surface with a coat of protector. With the roller, remove excess on the surface before it dries. Repeat for subsequent sections, maintaining a wet edge in order to prevent overlap marks. For a darker colour and a higher gloss, apply a second coat. Wait until the first coat is dry (+/- 4 hours), then apply a second coat following the same method as before.
Traffic: Pedestrian: 24 h. / Vehicular: 48 to 72 h. Block access during that period.
CAUTION
• Any new concrete product has the potential to produce efflorescence (whitish salts) on its surface. This Protector, like any film-forming coating, carries a small risk of trapping efflorescence beneath its film. Consult the pavermanufacturer or contact Techniseal for more information 1 800 465-7325. • Do not attempt sprayer application on windy days. • Do not apply this product over a blotchy or hazed surface. • Trimming with a brush or a roller could leave marks. • This product will make the surface more slippery when wet. If slipping is a problem, consider Surefoot Additive from Techniseal®. • An over-accumulation of product could lead to surface whitening. • Extreme climate or heavy traffic could limit product longevity.
CLEANING & DISPOSAL
Wash tools and hands with warm soapy water. Consult your retailer or municipality regarding the disposal of empty containers or unused product.
